Emco V10 & V10P output gear for the changewheel drive. 45 teeth, 2-pin steel hub. Original Part Number: C3Z-011-060. The gear supplied can be in white or black material.

Boxford, South Bend & Smart & Brown 100/127t inch to metric screwcutting transposing gear. This gear set will convert all imperial (inch) belt-drive Boxford lathes (except the late VSL Type), the South Bend 9-inch and the Smart & Brown Sabel, SAB and S lathes to cut metric pitches.

Boxford and South Bend Lathes: Metric to inch screwcutting conversion gear 127/135T

Raglan "5-inch" Tumble-reverse gear. This gear has 26 teeth in cast iron UK made by a precision engineer. If in doubt about which Raglan lathe you have, check our article here: http://www.lathes.co.uk/raglan  Tumble reverse gears for the earlier Raglan "Little John" are here: https://store.lathes.co.uk/parts/raglan-little-john-tumble-reverse-gear

A ring to repair a broken "bull wheel" on the main spindle of all Boxford belt-drive lathes except the Model VSL

Boxford lathe Tumble Reverse Gears 14.5 pressure angle - Early Models
This gear is for all Models prior to Serial Serial No. 11-13513 - the introduction of the Mk.2 Models that have a single lever on top of the headstock to engage the backgears. 32 teeth and a 14.5-degree pressure angle. Made in the correct grade of cast iron - we have sold these gears for over 30 years.
For later models (the Mk. 2 AUD, BUD and CUD) with a 20-degree pressure angle see here.

Rack-pinion gear for the Raglan "5-Inch" lathe - the gear that engages with the bed-mounted rack.

38-tooth gear to fit on the headstock spindle and engage with the headstock pulley as part of the backgear system.
The gear was made with two pressure angles:
1) 14.5-degrees for older lathes with a swing-type quadrant lever on the front face of the headstock, like this http://www.lathes.co.uk/boxford/img10.jpg

Raglan Little John Mk.1 and Mk.2 rack-pinion gear - the gear that engages with the bed-mounted rack. This gear has a single-diameter shaft with a Woodruff key slot and a machined flat.

RING GEAR to repair the main spindle Bull Wheel (the larger of the two gears on the main spindle). Machine off the damaged teeth and shrink or Loctite the new gear in place. Can be used on all belt-drive models the A, B, C, AUD, BUD, CUD, ME10, CSB and those T and TUD non-screwcutting lathes fitted with backgear - but not the VSL which had hardened backgears. PLEASE NOTE: this is a 14.5-degree gear, not the later 20-degree.

Changewheels for Boxford, South Bend "9-inch" lathes. A full range is available - but we have currently to rebuild this section of the website.
As the list is incomplete, please email tony@lathes.co.uk to order or phone 01298-871633   From overseas: +44-1298-871633   From The USA and Canada: 011-44-1298-8716308:00 to 23:00  Monday to Saturday

For Boxford Tumble Reverse gears - see here

Raglan "Little John" tumble-reverse gears to fit the Mk.1 and Mk.2 lathes - UK made by a precision engineer. If unsure which model of Raglan you have, see my article here: http://www.lathes.co.uk/raglan 
Tumble reverse gears for the Raglan "5-inch" lathe can be ordered here: https://store.lathes.co.uk/parts/raglan-5-inch-tumble-reverse-gear

Boxford & South Bend Backgear 24-tooth Shaft. We can supply - on a service-exchange basis - a backgear shaft fitted with a new steel gear. The large gear can be knocked off to save postage (though some early shafts were one piece). Early gears have a 14.5-degree pressure angle and have no markings to show this. Later gears are 21 degrees and in this case the shaft is stamped "21" - though it's sometimes hard to see. We can supply both types.

Boxford lathe Tumble Reverse Gears Late Models with a 20-degree pressure angle
This gear is for all Models after Serial Serial No. 11-13513 and the introduction of the Mk.2 Models that have a single lever on top of the headstock to engage the backgears. 32 teeth and a 20-degree pressure angle. Made in the correct grade of cast iron - we have sold these gears for over 30 years.

Boxford Lathe Tumble Reverse Gear - Late Models
This gear is for all Models after Serial Serial No. 11-13513 - the introduction of the Mk.2 Models that have a single lever on top of the headstock to engage the backgears. 32 teeth and a 20-degree pressure angle. Made in the correct grade of cast iron - we have sold these gears for over 30 years.
For earlier Boxford lathes with 14.5-degree changewheels, see here

Changewheels for Hobbymat MD65, Prazimat MD300, Saupe & Sohn, Hobby 120 Sliven and Proxxon version of the lathe: Individual gears are available in various sizes.
PLEASE NOTE: we do not have any 30t gears - if you order a 30t you will RECIEVE a 33t gear