Boxford VSL Boxford Lathe Vari-speed belt. Unfortunately, the exact belt is no longer available but one close can be supplied. In order to obtain the whole speed range, this will need 1/4" (6mm) packing piece between cross-shaft and hangers to increase the distance to the motor. However, this is not essential as only a little of the slowest speed will be lost if the belt is fitted "as-is". Sent insured by Royal Mail Special Delivery.
Raglan "Little John" tumble-reverse gears to fit the Mk.1 and Mk.2 lathes - UK made by a precision engineer. If unsure which model of Raglan you have, see my article here: http://www.lathes.co.uk/raglan
Tumble reverse gears for the Raglan "5-inch" lathe can be ordered here: https://store.lathes.co.uk/parts/raglan-5-inch-tumble-reverse-gear
Raglan "5-inch" Tumble-reverse gear. This gear has 26 teeth in cast iron UK made by a precision engineer. If in doubt about which Raglan lathe you have, check our article here: http://www.lathes.co.uk/raglan Tumble reverse gears for the earlier Raglan "Little John" are here: https://store.lathes.co.uk/product/19553
The correct drive belt for the Luna SP800, SP1000 & Woodman SP800 wood-turning lathes. Other sellers will have also branded these lathes under various names. The belts are 22 inches (559mm) long, 0.8 inches wide (10 mm) and have 4 small V-grooves on the drive surface. Fill in the belt width and length details below; the order will then work automatically.
A pair of Hobbymat - Prazimat Lathe belts. Top quality, made in Germany. For smooth, vibration-free running at high speedsof it is recommended that both belts be changed at the same time. One each of the two sizes: short and long.
A belt for the Hobbymat - Prazimat Wood Lathe Models MD120 and MD150 click here to order
A high-quality, English-made casting to make a T-slotted cross slide for Boxford and South Bend "9-inch" lathes. It is also possible to make a T-slotted slide for other 4 to 5-inch centre height lathes - in the case of the Raglan "Little John" and "5-inch" it can only be used as a boring table as it is not possible to mount the top slide on it. Machined only on the top surface these castings are long-term stored and so very stable - but they do need cleaning before machining.
Final drive belt for Boxford Underdrive lathes. For this application, 1.4 metres of A-section Nu-T-link is needed.
Tom Senior E-Type V-Drive belt. The correct marked size for this miller. In the box where it asks for length, enter 1000 - but you'll receive the correct belt. (Code 185ZZZ)
Boxford lathe Tumble Reverse Gears 14.5 pressure angle - Early Models
This gear is for all Models prior to Serial Serial No. 11-13513 - the introduction of the Mk.2 Models that have a single lever on top of the headstock to engage the backgears. 32 teeth and a 14.5-degree pressure angle. Made in the correct grade of cast iron - we have sold these gears for over 30 years.
For later models (the Mk. 2 AUD, BUD and CUD) with a 20-degree pressure angle see here.
Polycord Belting - immediate delivery from stock. This makes an excellent, long-life application for hard-worked machines - from models though engravers to small lathes and millers, etc. Our solid plastic belting is made in Switzerland and of the very best quality. We can produce belts of practically any length down to 140 mm long using a jigged joint and heat weld. Although all belts stretch, Polycord is more resistant than most, especially when 6mm in diameter or over.